Search Results:
- If you will be tested on the IPC then we recommend to read the chapter before the class and write the differences in as you go through the materials, if any. How hard is the journeyman plumbing test? The journeyman plumbing test is very hard. You...
- This class includes: Over 14 hours of class covering every chapter about an hour a day Sizing of water distribution, sewers, vents and gas piping as well as storm drainage roofs Practice quizzes to prepare for the real exam A full-length, 2-hour...
- HomePrep is a National Leader in online educati… Requirements To Complete About This License A Journeyman Plumber license allows for the installation, maintenance, alteration, and repair of plumbing fixtures and systems under the direction of a Master Plumber. A Master Plumber is a person who performs or contracts to perform plumbing services. Class 1 is restricted to plumbing work involving single-family dwellings, one-level dwellings designed for no more than 2 families and commercial structures not exceeding 10, sq. Class 2 license has no restrictions as to the type of plumbing work allowed. Pre-approval from the state is required to sit for the examination. Applicants must be able to document at least 3 years of plumbing experience, to qualify for the Journeyman's exam Class 1 - 5 years experience with a minimum of 2 years as primary experience. Class 2 - 5 years experience with a minimum of 2 years as primary experience. The application must be submitted to the Board at least 60 days before the next scheduled exam date.
- Applicants should receive an approval letter approximately 30 days prior to the exam. After the exam, passing candidates will receive their licenses in approximately six weeks. If you need assistance with the application process, Home Prep- a division of Stautzenberger College can help you by saving you time and money.
- With our years of experience, we can quickly and accurately submit your application to your state. However, they can NOT be taken into the exams. These references are available for purchase from our online contractors' bookstore or by calling The following references are also needed to study for the exam. They are available to print online free of charge.
- Many of the questions have been on recent Red Seal plumbing exams. Hal Hokanson halhoke. Below are some other questions and topics that have been found on recent plumbing exams. What is done to a Natural Gas line after Installation? What is the rough to center of flange for a close couple toilet? What is the Control Voltage between v and 24v zone valve transformer? What is the minimum offset distance in a horizontal piece of pipe which has 60 FU?
- Where is the circulator on a hot water boiler installed? What is the first thing done after installing drainage piping in a home? What is the minimum amount of backfill over septic piping? Know various things about AC units; such as where is an AC unit vent installed in a wall? What are the wires in a 4 wire zone valve designed to do? Know your Survey Readings and calculations. Know Pipe Slope Calculations. Know how to size water and drainage lines. How is the drain of a Water Dispensing Fridge hooked up? How is vertical piping suspended? What is the distance between hangers on 6" Cast Iron pipe? What is wrong with the pump installation if the pump turns on immediately after running water? What pump is designed for shallow well applications? Where is the jet in a deep well pump located? If a septic field is located 50m from the tank up a hill, how would the effluent be distributed? What is the pressure on a 6" gate valve if the line pressure is 60 psi? What would increase the length of flush for a Urinal?
- When would it be ok to tie a floor drain into a Leader? Where is the drain from a sump pump tied into? How many showers can be installed using one drain? Minimum distance between shower heads? What type of Backflow preventer is used for Medium Hazard with no treatment? What Backflow preventer cannot be tested? How is copper attached to steel to prevent rusting? What would be done if the test punch of a Hilti didn't mark the metal? What would be done with the Hilti is the pin was damaged? What is meant by malleable? How much would copper pipe expand if the temp increased by 50 deg C? What could be done to a toilet to stop condensation?
- What fixture should be completely impervious to water? What determines the size of the piping from a well? What determines the size and design of a septic system? What is the weakest type of pipe weld? What type of pipe doesn't use fitting allowance? What joins laboratory glass pipe? What drawing would be used to determine how many clevise hangers to use for a job? After installation of a medical copper line, how is the pipe cleaned before use? What type of solder is used on domestic water lines? Pipe offset calculations. Rain water Leader Calculations and tables. How would you secured ready rod to a concrete ceiling? Know where to find Rod Thicknesses in code book. Know how to figure out sump pump liter per second calculations? How is testing done to water lines in freezing temps? What is the maximum length of a fixture outlet pipe on a double compartment sink?
- What is the maximum distance between fixture and grease trap? Know about oil interceptor; including size of vents, how many, etc? How high does a vent terminate on a sun deck? What is the distance a vent can be installed from a property line? What is the grade at which pipe is graded in a septic field? What is the maximum distance for one way rodding on a 4" line? What should be installed in a man hole after 1 meter depth? What is the maximum pressure for domestic water? What is installed on a Roof Hopper? What is required in order for a Building Trap to be installed? What Backwater Valve is prohibited? If part of the drainage system is subject to backflow, what and where could be installed?
- What is the vertical distance the drainage from a WC can be? What is the maximum degree change on a kitchen sink, before installing a cleanout? What is the main purpose of a siamese connection? Where is the Fire Line Connected? If a bypass is installed around a meter, what size is the piping? What type of bolts are used to mount the toilet bowl to the flange? What would be the easiest system design and installation for Zone Valve placement? What is needed installed in a home before installing a condensing boiler? What is needed to be installed for a building drain? What size is a 4" Vent Header increased to before exiting a roof?
- Know how many Roof Drains are needed if using Flow Controls? What is used on a Heating System to allow for expansion and contraction? What is used on a Cooling System to allow for expansion and contraction? What is installed on fixture drain if below grade? What is the minimum pipe size for water distribution? Where is the flow control installed in a hydronic system? What allows for air to enter around laterals in a septic field? What is the indication for hard water? How does a water softener convert hard water? What is the natural means to power a water pump?
Plumbing Technology: Plumber's Licensing Exam And Study Guides
What is the lift on a shallow well pump? Where should a fin tube rad be installed in a room? What is the reason for clear water during a boiler blow down? What is the maximum change in direction in a circuit vented branch? Calculate the distance between 6 double vented urinals on a wall, equally spaced? What can a double TY be used for? What are the sizes of Nominal Pipe Size? Don't confuse with National Pipe Thread When repairing a rusted cast stack above concrete floor, what should be done first? Disclaimer The information on this site is for informational purposes only. PlumbingHelp, its affiliates and content licensors assume no liability for any inaccurate, incomplete information or the outcome of any project. Always consult your local authority regarding plumbing codes for your area.- COVID Update: We are continuing to support and deliver our information modules to all trades people looking for assistance for their Red Seal exam preparations. All modules will continue to be delivered the same way to customers via email for same day delivery services. Stay healthy and safe. Thank you. Scroll down to view sample questions. We will send you all the information via email immediately so you can start studying while you wait for the disk package delivery. Use PayPal for safe and secure method of payment.
- Just click on the "Buy Now" button to complete your order. Emergency repair work like unclogging drains, or repairing water main ruptures, represents a significant part of their knowledge and experience. They may have to alter structures to accommodate the pipes by roughing in after the frame and roof of a new building are in place. They study the building plans to determine the layout for plumbing and related materials, locate and mark positions for connections and fixtures, cut holes through walls and floors, select the type and size of pipe required and measure, cut, thread, bend, clamp, solvent cement or solder pipe assembly and install valves and fittings securely in position. Once this is completed they test the pipe systems for leaks. Plumbers will then return to the construction site after plasterers or dry wall installers, tile setters and floor covering installers have completed their work to do finishing work such as installing sinks, tubs and toilets.
- As an experienced plumber, you might specialize in sheet metal work on industrial, commercial or historical buildings. Some Plumbers also braze and weld metal. A Plumber's specialization is based on his or her knowledge of the substance being carried. Plumbers often work in the construction industry, laying new pipe for buildings or doing extensive renovations to large buildings. Plumbers also sometimes make use of other related skill sets, such as a familiarity with basic welding and electrical work and a limited amount of gas fitting work. Industry Changes While a plumber is the first occupation associated with the industry, pipe layers, pipe fitters and steamfitters represent a large portion of the job market. Over the next ten years, the employment outlook is considered to be excellent. The lack of trained and qualified servicemen and the expected increased retirement rate in these trades over the next decade highlight the opportunities within the industry for potential jobs.
- The government has recently set targets for greater energy efficiency to combat climate change. With further training, you may be able to install and maintain renewable energy technologies like solar powered heating systems. A surge in water consumption legislation in the previous decade has prompted manufacturers to create more efficient and environmentally friendly products from low-flow and waterless to dual-flush and macerating fixtures. Consumers are increasingly educated regarding construction products and materials, resulting in a demand for more sophisticated and multi-functional products. Sustainable and eco-friendly design is a major focus of the building and construction industry. In the next decade smart home and bath products will be in demand, such as the 'Intelligent Toilet' system made in Japan which can measure sugar levels in urine, blood pressure, body fat and weight. In the ideal environmentally-correct home of tomorrow, toilets will flush water recycled from the washing-machine or dish-washer.
- Safety Safe working practices and accident prevention are the primary importance to the health and safety of all person s at any or all work place environments. All person s including employee, employer and government, share this responsibility in order to keep everyone free of any dangers or accidents that may cause an individual s serious bodily harm or death.
- Health and safety has become a high priority in the workplace due to increased awareness of dangers and the identifications of hazardous materials. Practicing health and safety is a tremendous contribution to a safe and accident free work place environment. Air-conditioning and Heating equipment except window type units Baseboard heaters, electric, non-portable Boilers e.
- All of the above Trusses are engineered. Regardless of whether they are roof trusses or floor trusses, they must not be cut, notched, drilled, spliced or otherwise altered. When truss integrity is disturbed it can lose its structural ability. Normal cutting, notching and drilling procedures associated with solid wood joists and rafters do not apply to trusses. There are, however, some occasions when a truss must be altered to allow for a plumbing installation. When this is the case, an approved engineer must provide written details on how the truss can be altered to allow for a plumbing installation. Only an engineer can do this. Incorrect answer. Please choose another answer. Mechanical joints are prohibited from joining materials of different types. True False Mechanical joints are approved for joining materials of dissimilar type as well as materials of the same type.
- Fixtures 7. What is the maximum distance an employee of a department store should have to walk to reach a suitable restroom facility? During this walk they are not required to ascend more than one set of steps. Bathrooms under these conditions cannot be installed more than one story above the work area. There are possible exceptions for buildings that house factory workers or industrial workers.
- The foot rule is the typical standard, but you should check your local code to confirm the local requirements. The accessible travel route for people going to use public plumbing facilities must not pass through a kitchen. True False Accessible routes for travel to public restroom facilities are not allowed to pass through kitchens, storage rooms, closets or similar spaces. What is the maximum distance that a lavatory faucet for accessible use can be placed from the front edge of a lavatory? Indirect and Special Wastes Which of the following is considered to be the best method for connecting an indirect waste to a sanitary drainage system? Air gap c. Both a and b are equal d.
- None of the above An air gap is believed to be superior to an air break for the protection of an indirect wastepipe from back siphonage. Due to the nature of installation there is more risk of a backflow occurring with an air break. Since air breaks have discharge piping entering a receptor it is feasible to have the sanitary drain become clogged and back up, which could result in contaminated waste traveling back to the indirect waste fixture.
- This is not possible when an air gap is used. Which of the following locations is not an acceptable location for an indirect waste receptor? Closets c. Both of the above d. None of the above Indirect waste receptors are not to be installed in closets or unvented areas. All indirect waste receptors are required to be accessible. Clear water waste from a potable source, such as a relief valve on a water heater, must be piped to an indirect waste through an air gap. True False Clear water waste from a potable water system is to be piped to an indirect waste and must discharge through an air gap. This is as simple as having the discharge pipe terminate six inches above the strainer of a floor drain.
- Vents and Venting Which of the following types of fixtures can be served by a combination-waste-and-vent system? Urinals c. Sinks d. Bidets Combination-waste-and vent CWV systems do not require independent vents on all fixtures. Instead of a vertical vent the fixtures approved for a CWV installation are installed with oversized drains. Due to the larger drain diameter the fixture obtains the needed air for drainage in the top section of the oversized piping. Urinals, toilets and bidets are not allowed to be installed on CWV systems. Circuit vents can do which of the following? Tie into stack vents b. Tie into vent stacks c. Tie into another vent that extends to outside air d. All of the above Circuit vents are used when venting a battery of fixtures. The vents may be tied into other vents that extend to outside air. This includes vent stacks and stack vents. The diameter of a circuit vent must be at least one-half the size of the drain that it is serving.
- Vented b. Covered with a gas-tight cover c. Placed outside of any habitable structure d. Both a and b Sumps for sewage pumps that remove sanitary waste are required to be vented to outside air. The vent cannot be tied into a general venting system if a pneumatic sewer ejector pump is to be installed. When a typical sewer pump is to be used the vent can tie back into a general venting system. Generally, the minimum diameter of a vent for a sewage sump will be required to be two inches in diameter. In addition to proper venting, sewage sumps must be equipped with gas-tight covers. Traps and Cleanouts If three degree bends are used to make an offset, a cleanout is required at the top of the horizontal drain within 24 inches of where it connects with the last degree bend.
- True False Cleanouts are not required when a drain pipe makes a turn of no more than 45 degrees. The fact that three degree fittings are used to make an offset is not reason to require the installation of a cleanout. When can a cleanout be used for the installation of a new fixture? In other words, what makes it acceptable to remove a cleanout plug, replace it with a male adapter and then extend piping from that point to a new fixture? Never b. When approved by the master plumber who has been issued a plumbing permit c. When another cleanout is provided d.
- When approved by a code enforcement officer and another cleanout is provided to replace the one being used as a connection point of drainage piping for a new fixture. Fittings housing cleanout plugs are not allowed to be used as a connection point for a drainage pipe that will serve a new fixture, unless the connection is approved by a code officer and a new cleanout is provided to replace the cleanout being changed over to a connection point for drainage piping. Which of the following are acceptable types of cleanouts? A rubber cap that is installed with a stainless steel clamp c.
- If so, you will more than likely be required to take a plumbing pre-apprenticeship aptitude test. Let JobTestPrep prepare you for your plumber assessment test today and apply with confidence. Taking a test tomorrow? Knowing what you will find on the plumbing apprenticeship aptitude test can contribute significantly to a successful result. You can expect two main sections. This is a timed test that takes an average of 1 hour and 20 minutes.
- The questions involve 9th Grade — 12th Grade material. Taking a plumbing practice exam and reviewing a plumbing exam study guide will familiarize you with the types of questions and test format that you will encounter on the actual exam. Test preparation will also highlight the subject areas that need further practice. The plumbing apprenticeship test is a standardized exam that covers the subject matter used by plumbers on a daily basis.
No comments:
Post a Comment